NOV Fiber glass systems is the leading worldwide manufacturer of fiberglass reinforced thermosetting resin pipe products used primarily for onshore and offshore corrosion control, in an extensive range of low to high pressure applications.

Wenco is the licensed distributor in Australia of NOV FGS products.

FGS piping systems employ a variety of epoxy and vinyl ester resins and corrosion barriers. This integration of innovation and quality achieves optimum performance characteristics for virtually any harsh applications. FGS piping engineers' and fabricators' expertise specifies the design and manufacture of our joining systems and fittings, incorporating a wide variety of mechanical and bonded systems. These ensure precision installation, optimum system performance, unmatched ease of assembly, and surpass customer requirements.

FGS products solve the problems inherent in traditional materials in tough applications and follow the NOV philosophy of giving our customers a competitive advantage by providing value, innovation and DELIVERING EXPERIENCE.

NOV Accreditation Letter


Fiber Glass installation

 

Wenco Pty Ltd is specialized in Composite Piping Systems (Fibreglass) GRE, GRP & GRVE. We are the Leading Supplier and Installer of Composite and Mechanical Piping to the Mining, Oil & Gas and Construction Sector Providing Quality Piping Systems across Australia and around the globe. We provide fabrication and installation of fiberglass piping systems to help companies deal with the environmental issues created by the corrosion of steel pipe.


With 40+ years of experience in the fiberglass field Our Piping system has endless application, few listed below:

  • Saltwater and seawater lines
  • Oil field reinjection systems
  • Brackish water lines
  • Crude oil transmission lines
  • Fire protection systems
  • Temporary pipelines
  • Potable water lines
  • Electrical conduit
  • Waste water and sewage systems
  • General industrial service for mildly
  • Drainage systems corrosive liquids
  • Ballast water
  • Fresh water

We offer an extensive range of piping services:

  • Pipe erection
  • Pro spooling and Testing
  • On site repair and modifications
  • Non-destructive testing (NDT)
  • Hydro testing
  • Pigging
  • Bolt torqueing
  • Painting & Coating
  • Stress Analysis

Our personnel are trained and qualified to carry out hydro testing of all fabricated and installed piping systems using NATA certified and calibrated testing equipment. Wenco has in-house training facilities with training carried out by an ISO 14692 Part 4 approved and accredited trainer.


Fiber Glass Columns, Pressure, Tanks

Wenco design, manufacture and erect Field Storage Tanks, Reaction Vessels, Pressure Vessels, Wet Gas Electrostatic Precipitators, Scrubbing Systems, Exhaust Systems, Polymer Concrete Cells, Gratings, and Linings etc.

Applications

  • Fertiliser
  • Mining
  • Metallurgical
  • Water & Wastewater Treatment
  • Pharmaceutical
  • Chemical
  • Food Processing
  • Paper & pulp
  • Railways
  • Pigments and Dyestuff
  • Engineering
  • Paints
  • Textile

Design

Majority of products are custom-made conforming to the International standards like:

  • BS 4994: 1987
  • ASTM D 3299 - 81
  • ASME - Section X
  • ASME RTP-1-2000
  • AD 2000 - Merkblatt N1 f. NBS Voluntary Products Standard, PS 15 - 69

Why GRP?

The MAIN characteristics of thermosets (literally 'setting under heat') is that they require curing, when they undergo a molecular cross-linking process which is irreversible and renders them infusible. They thus offer high thermal stability, plus good rigidity and hardness and resistance to creep. It also means that, once cured, the resin and its laminate cannot be reprocessed, except by methods of chemical break-down, which are currently under active development. For practical purposes, therefore, cured thermosetting resins can be recycled most effectively if ground to fine particles, when they can be incorporated into new laminates, as cost-effective fillers.

Thermosetting resins have little use as pure resin, but require addition of other chemicals to render them processable. For reinforced plastics, the compounds usually comprise a resin system (with curing agents, hardeners, inhibitors, plasticisers) and fillers and or reinforcement. The resin system provides the 'binder', to a large extent dictating the cost, dimensional stability, heat, chemical resistance and basic flammability. The reinforcement can influence these (particularly heat-and dimensional-stability), but the man effect is on tensile strength and toughness. High-performance fibres, of course, have a fundamental influence on cost.

Special fillers and additives can influence mechanical properties, especially for improvement in dimensional stability, but they are mainly used to confer specific properties, such as flame retardancy, UV stability or electrical conductivity.

Thermosetting resins are normally used in the liquid state and solidify and harden on curing. With some resins it is possible to part-cure and then hold the resin in what is termed the B-stage, for the cure to be completed at later time.


Fiber Glass Commercial Vessel

NOV Fiberglass Systems glass reinforced epoxy piping is chosen for all commercial vessels including specialized vessels, oil tankers, gas carriers, car carriers, bulk carriers, and container vessels. The latest series of large container carriers are all fitted with Bondstrand™ Series 2000M piping.

Lightweight

Over 900 meters of pipes of sizes from 1.5" to 20" are installed on these 18,000 TEUs Container vessels. The Triple E Vessels: Economies of Scale, Energy Efficient and Environmental Efficient, benefit from weight savings of over 54 tons (vs Schedule 40 Carbon Steel Pipe), the light weight translates into fuel economy advantage or higher load capacity.


Fiber Glass Platforms

Wenco engineers and skilled personnel and highly experienced to carry out any form of work. Wenco owns a broad range of equipment to assist the fabrication processes including cutting, shearing, bending and rolling machines alongside Plasma Cutters, Metal Inert Gas Welding (MIG)/Flux Core, Manual Metal Arc Welding (Stick) and Tungsten Inert Gas Welding (TIG).

Our workshops are equipped with all the necessary facilities to carry out pre-fabrication of spools and platforms.

Our workshops are equipped with different facilities, few listed below:

  • In-house pipe spooling facilities
  • In-house material handling facilities
  • Welding equipment availabilities
  • Experienced skilled personnel's availability
Wenco PTY LTD
CONNECT WITH US
Fill out the form below to contact us or request one of our representatives to contact you. Thank you!
Thank You. We will contact you as soon as possible.

Call us at
+61 8 9267 5500

Services Inquiry Form

GET YOUR MONTHLY FIX
of Wenco Group News
Simply drop your details in below and we’ll send the latest Wenco news to your inbox each month.